WEEK 17: SUBMIT PROPOSAL & DRAFT CHAPTER 1, 2, 3

OBJECTIVE

1. To submit a complete proposal and draft of chapter 1, 2 and 3 of my FYP 1.
2. To complete FYP 1 semester.

METHODOLOGY

1. Compile the draft of chapter 1, 2 and 3.
2. Final consultation with supervisor before submitting the proposal and draft report.
3. Log in the UniKL VLE to submit the proposal and draft report of FYP 1.
4. Submit the proposal and draft report with the slides presentation of my FYP.

RESULT

The proposal and draft report have been submitted through the UniKL VLE on May 30th, 2018. The following figure is the proof of my submission.

SUBMISSION OF PROPOSAL AND DRAFT REPORT

ANALYSIS/DISCUSSION

The proposal, draft report and slides presentation have been submitted on May 30th, 2018. The proposal, draft report and slides presentation was already submitted on May 26th, but there was some problem on submitting the draft report. The draft report should be included with the plagiarism check and after checking the plagiarism the draft report was resubmitted. The plagiarism check took a lot of time since the website to check was already full and I have to wait for other student to log out. However, it was already exceeded the due date because of mistaken submission of my draft report.

CONCLUSION

In conclusion, the objectives of this week was achieved. The proposal, draft report and slides presentation was submitted on May 30th, 2018. Although it was already exceeded the due date, my supervisor have already been notified the cause of it.

WEEK 16: CHAPTER 3: METHODOLOGY (DRAFT)

OBJECTIVE

1. To write a complete draft of methodology for FYP 1.

METHODOLOGY

1. Discuss with supervisor on how to write methodology for FYP.
2. Follow the FYP report template given by the UniKL to help writing the methodology.
3. Gather every information regarding designing a quadruped robot from any journals or articles in internet.
4. Include the block diagram, flow chart and gantt chart in the methodology draft.
5. Produce a complete methodology draft for FYP 1.

RESULT

The figures below are the complete draft of methodology for FYP after verified by my supervisor.

Methodology Draft

ANALYSIS/DISCUSSION

The draft of methodology for my FYP project includes the block diagram, flowchart, hardware and software descriptions and circuit diagram. The methodology was only a draft since the project is not yet build and the complete methodology will be done in FYP 2 after developing the project.

CONCLUSION

In conclusion, this week objective was achieved. The chapter 3: Methodology draft was completed and verified by my supervisor. This methodology will shows the readers on how to develop a quadruped robot using internet of things (IoT) platform.

WEEK 15: CHAPTER 2: LITERATURE REVIEW (DRAFT)

OBJECTIVE

1. To write a complete draft of literature review for FYP 1.

METHODOLOGY

1. Discuss with supervisor on how to write literature review for FYP.
2. Follow the FYP report template given by the UniKL to help writing literature review.
3. Gather every information regarding quadruped robot from any journals or articles in internet.
4. Produce a complete literature review draft for FYP 1.

RESULT

The figures below are the complete literature review draft after discussed with my supervisor.

Literature Review Draft

ANALYSIS/DISCUSSION

This literature review is produce after a few research from journals and articles. However, this literature review was only a draft and if there's any addition to be made will update in the future.

CONCLUSION

In conclusion, this week objective was achieved. The literature review draft is to guide readers on past research and project of quadruped robot. Some of the past research have similarities to this prototype project.

WEEK 14: CHAPTER 1: INTRODUCTION (DRAFT)

OBJECTIVE

1. To write a complete draft of introduction for FYP 1.

METHODOLOGY

1. Discuss with supervisor on how to write an introduction for FYP.
2. Follow the FYP report template given by the UniKL to help writing introduction.
3. Gather every information regarding the project to help write the introduction.
4. Produce a complete introduction draft for FYP 1.

RESULT

The figures below are the complete introduction draft after discussed with my supervisor.

Introduction Draft

ANALYSIS/DISCUSSION

This introduction project is just a draft. However, if there's any changes made on the project the report draft will be altered but for the mean time this will be the introduction use to show to the supervisor. 

CONCLUSION

In conclusion, this week objective is achieved. The main reason to write the introduction project is so that readers can understand the reason why this project is propose and develop.